Today's watch detective to bring you the Omega Seamaster strap how to remove the sharing, I hope to add new knowledge to you, need to know more about the Omega Seamaster watch can be concerned about theWatchdog website哦。Omega-home系列，在2009年迎来了一次重大变革，整个系列的元素都非常引人注目，欧米茄Seahorse Series诞生于1948年，以极富传奇色彩的在全世界收获了无数的荣耀，他的海马标志代表着精准度和可靠性！
How to remove an Omega watch band.文章源自表探复刻-https://www.bbtwatch.com/en/wbzs/58346-html
1. When disassembling the strap, both the left and right sides of the strap are required to be symmetrical, but this does not mean that the number of sections on both sides of the strap must be the same, so the strap folding form is also different, and it is only required that the buckle and the watch are parallel, which is more beautiful.文章源自表探复刻-https://www.bbtwatch.com/en/wbzs/58346-html
2. watches like Omega, the new strap buckle buckle is actually biased, so generally only need to remove a section on the strap, basically, unless the wearer's wrist is too thin, if you want to cut off a lot of the strap section, you have to consider intercepting from the ends of the strap. On the inside face of the band is engraved with an arrowhead indicating the orientation of the piercing nails, the installation of the opposite, the top arrow to load.文章源自表探复刻-https://www.bbtwatch.com/en/wbzs/58346-html
Steps for removing the strap.文章源自表探复刻-https://www.bbtwatch.com/en/wbzs/58346-html
1) Place the strap on the plastic bracket and determine the position to be cut and the direction to thread the pegs.文章源自表探复刻-https://www.bbtwatch.com/en/wbzs/58346-html
(2) First use a larger diameter wire punch, vertical to the head of the piercing nails, with a hammer to hit a little length, at this time, pay attention to, under the bracket to leave a hollow, so that the piercing nails can continue to hit out.文章源自表探复刻-https://www.bbtwatch.com/en/wbzs/58346-html
(3) Change a smallest diameter of the wire buckle, carefully against the head of the strap, and hammer hard, so that the strap will be broken little by little. If you feel nervous in the process, light hit but wear nail has not come out of the head, you have to stop and observe, there are only two possibilities, one is the wire punch is relatively thick, and then once the punch is not aligned with a good wear nail.文章源自表探复刻-https://www.bbtwatch.com/en/wbzs/58346-html
(4) When the piercing nail is smashed to a length of about 1 cm, the piercing needle should be clamped with pliers, pulled out with force, and then separated, and the casing in the strap section should be taken out in time to prevent loss.文章源自表探复刻-https://www.bbtwatch.com/en/wbzs/58346-html
(5) When reconnecting the strap, first check that the sleeve is in the strap section . Determine the direction of the piercing nails and the direction in which they were smashed in.文章源自表探复刻-https://www.bbtwatch.com/en/wbzs/58346-html
(6) When you first start to put in the nails, you have to hit them directly with a hammer, but when the penetrating nails go through the joint between the two belt sections, you have to check that there is no misalignment, and you can only continue to hit the penetrating nails if you have aligned all their holes.文章源自表探复刻-https://www.bbtwatch.com/en/wbzs/58346-html
(7) When the wearing nail is almost broken, at this time to replace the steel wire punch, available thicker punch, such as 1.0 mm, continue to press into the wearing nail, because the diameter of the small steel wire punch, it is very easy to slip, resulting in the appearance of the strap damage.
